History of 911
Why 9-1-1?
When designing the first emergency response system, the first question that needed to be answered was which numbers to use. Why was 9-1-1 selected?
When the task force convened to consider such a question, some initial parameters were set. It was going to be a three-digit number, and the first digit could not be "1" or "0."
When this system was originally put in place, most people were using rotary dial phones. For expediency, there was no question that the second and third numbers should be "1." So the real debate centered on which first number to use.
Among the most compelling reasons for settling on "9" was that it would be easy to find in the dark. Simply, locate the last hole on the dial, the "0" and back up one. Or for a touch pad, find the bottom right button, the "#" and move up one.
Thus, the emergency 911 code was born.
At this point in 911's history, it was very important that the dispatcher at the PSAP obtain information from the caller about where he or she was and what kind of emergency service was required, then dispatch the correct authorities. As you might imagine, this required some skill in dealing with people under the stress of an emergency. Even then, details about where to send responders could often be hard to get.
When designing the first emergency response system, the first question that needed to be answered was which numbers to use. Why was 9-1-1 selected?
When the task force convened to consider such a question, some initial parameters were set. It was going to be a three-digit number, and the first digit could not be "1" or "0."
When this system was originally put in place, most people were using rotary dial phones. For expediency, there was no question that the second and third numbers should be "1." So the real debate centered on which first number to use.
Among the most compelling reasons for settling on "9" was that it would be easy to find in the dark. Simply, locate the last hole on the dial, the "0" and back up one. Or for a touch pad, find the bottom right button, the "#" and move up one.
Thus, the emergency 911 code was born.
At this point in 911's history, it was very important that the dispatcher at the PSAP obtain information from the caller about where he or she was and what kind of emergency service was required, then dispatch the correct authorities. As you might imagine, this required some skill in dealing with people under the stress of an emergency. Even then, details about where to send responders could often be hard to get.
Enhanced 911
When a call goes out from your phone, your voice isn't the only thing being transmitted in the network. The phone company switch that serves your phone is also sending out an Automatic Number Identification (ANI) signal to the network.
Originally, ANI signaling was designed to assist the phone company in accessing toll charges for long distance calls. With advances in technology, it was eventually employed to aid in relaying needed information to the PSAP for 911 response.
How does it work? Within each call, information containing eight digits is embedded in the signal. These eight digits contain the seven digits of the caller's local number. The eighth digit is called a Numbering Plan Digit (NPD). NPD is basically shorthand for the area code of the originating call. Since most 911 tandems rarely dealt with more than two or three area codes, this was an economical way to relay information with one digit instead of three.
With special equipment, the 911 tandem can read the ANI information and route the callback number to a digital display at the appropriate PSAP. Armed with this ANI information, the PSAP has equipment allowing it to request and receive the caller's physical address or Automatic Location Information (ALI).
With this enhancement, the PSAP is no longer totally dependent on obtaining location and callback information from the caller. Instead, the dispatcher can concentrate on helping the caller through the crisis, while instantly passing along needed information to the correct authorities.
This is how E911 has been working for more than 20 years when dialed from a wireline phone. With the advent of wireless phones and the need for wireless 911, additional challenges present themselves.
When a call goes out from your phone, your voice isn't the only thing being transmitted in the network. The phone company switch that serves your phone is also sending out an Automatic Number Identification (ANI) signal to the network.
Originally, ANI signaling was designed to assist the phone company in accessing toll charges for long distance calls. With advances in technology, it was eventually employed to aid in relaying needed information to the PSAP for 911 response.
How does it work? Within each call, information containing eight digits is embedded in the signal. These eight digits contain the seven digits of the caller's local number. The eighth digit is called a Numbering Plan Digit (NPD). NPD is basically shorthand for the area code of the originating call. Since most 911 tandems rarely dealt with more than two or three area codes, this was an economical way to relay information with one digit instead of three.
With special equipment, the 911 tandem can read the ANI information and route the callback number to a digital display at the appropriate PSAP. Armed with this ANI information, the PSAP has equipment allowing it to request and receive the caller's physical address or Automatic Location Information (ALI).
With this enhancement, the PSAP is no longer totally dependent on obtaining location and callback information from the caller. Instead, the dispatcher can concentrate on helping the caller through the crisis, while instantly passing along needed information to the correct authorities.
This is how E911 has been working for more than 20 years when dialed from a wireline phone. With the advent of wireless phones and the need for wireless 911, additional challenges present themselves.
PHASE 1 & PHASE 2 WIRELESS CALLS
Prior to the FCC order, the effectiveness of calling 911 from your wireless phone had backtracked to the days of relying on the caller to relay the proper information. This presented an additional challenge because now the caller may not even be at a fixed address - he or she could be on the side of the road, in the woods, or in an unfamiliar place. Obtaining accurate location information from the system is critical because getting it from the caller is even more unreliable.
The first phase of sending this information to the correct PSAP is for the callback number and cell tower of origination to be relayed to the PSAP.
So what happens? When a wireless subscriber initiates a call, the closest tower picks up the signal. The wireless service provider's network also has a switching center that works much like the switches on wireline calls. It reads the digits and forwards the calls accordingly.
The wireless service provider must first program its tower to immediately send any 911 call to the appropriate 911 tandem.
First, there is the Pseudo ANI (PANI). This number identifies the cell face (up to three per tower) or just the tower itself. This can narrow down the location of the caller to several hundred square meters at best, but more often several square kilometers. In addition, there is the Wireless Subscriber's callback number, which is sent along the signal. From the 911 tandem, the PANI, callback number and the voice are forwarded on to the appropriate PSAP. In most Phase I deployments, the callback number is part of the ALI response message.
The first phase of sending this information to the correct PSAP is for the callback number and cell tower of origination to be relayed to the PSAP.
So what happens? When a wireless subscriber initiates a call, the closest tower picks up the signal. The wireless service provider's network also has a switching center that works much like the switches on wireline calls. It reads the digits and forwards the calls accordingly.
The wireless service provider must first program its tower to immediately send any 911 call to the appropriate 911 tandem.
First, there is the Pseudo ANI (PANI). This number identifies the cell face (up to three per tower) or just the tower itself. This can narrow down the location of the caller to several hundred square meters at best, but more often several square kilometers. In addition, there is the Wireless Subscriber's callback number, which is sent along the signal. From the 911 tandem, the PANI, callback number and the voice are forwarded on to the appropriate PSAP. In most Phase I deployments, the callback number is part of the ALI response message.
However, number portability presents a challenge to the system. Today, with the explosion of phone numbers needed for wireless service, pagers, fax and Internet access, the use and number of area codes is in abundance. In addition, wireless phones can now roam all over the country.
Remember the eight-digit number used in wireline calls? There were only four Numbering Plan Digits equaling four area codes. This is no longer adequate.
The capability to use the actual area code and a new signaling protocol between the 911 tandem and the PSAP has required new software to be installed in our 911 tandem switches.
Phase II of bringing wireless 911 to the public means the PSAP has to receive fairly accurate location information from the wireless subscriber. How accurate? Depending on the technology, anywhere from 50 square meters to 300 square meters.
The responsibility of getting this information from the callers falls to the wireless service providers.
Remember the eight-digit number used in wireline calls? There were only four Numbering Plan Digits equaling four area codes. This is no longer adequate.
The capability to use the actual area code and a new signaling protocol between the 911 tandem and the PSAP has required new software to be installed in our 911 tandem switches.
Phase II of bringing wireless 911 to the public means the PSAP has to receive fairly accurate location information from the wireless subscriber. How accurate? Depending on the technology, anywhere from 50 square meters to 300 square meters.
The responsibility of getting this information from the callers falls to the wireless service providers.
How did I get My Address?
An address is one of those things in everyday life that is so commonplace that we don’t often think of it unless there is a problem that arises as a result of incorrect addressing – mail is incorrectly delivered, a package is not received, or 911 is called and responders have trouble locating a property.
So…how did I get my address, anyway?
In 1980, an addressing task force was formed in anticipation of the 911 system becoming mandatory in the state in 1983. Previous to that time, rural Scott County was addressed as “Route and Box” numbers, with no official street names. The task force found the municipalities were already using unique addresses, and the cities wanted to stay on their own addressing systems. So, an Addressing Ordinance was adopted by the eleven townships and the city of Elko. Recently, the combined cities of Elko New Market have also chosen to adopt this ordinance.
The Uniform Addressing Ordinance placed the eleven townships and Elko on a grid, with Baseline Avenue as the “zero” point in the county for E-W addresses. Addresses running generally in this direction receive street NAMES. Streets running generally N-S receive street NUMBERS and the grid runs from 115th St in the north, to 280th St in the south, the southernmost border of the county, Highway 19. Properties on the north and west sides of the street are assigned even numbers, those on the south and east sides of the street are assigned odd numbers. Numbering allows 1000 numbers per mile, or 500 for each side of the road.
When a new plat is recorded, the Addressing Coordinator will assign house numbers according to the addressing grid. New developments are checked to ensure the same street name is not used within townships, emergency service zones, or postal areas. These new addresses, including house numbers and street names, are then sent to the 911 Board, the Sheriff’s Office, the Fire Department and Ambulance service covering the area of development, the school district, voter registration, utilities, and the developer. The developer is responsible for placing street intersection signs within the development, with sign standards consistent with county policy.
The addresses are also added to the Computer Aided Dispatch system used by the dispatchers to take calls and send them to officers in their squads, and a mapping program that will plot (map) calls for the dispatcher when a call is received. That same database used in the mapping program is also used to populate the street names for the maps on the Scott County website.
When a resident applies for a building permit for a home, the address assigned to the particular lot on the plat is recorded on the permit and entered into the taxation records with a parcel ID number, or PIN. The data from this entry is used to populate the house numbers for the maps on the Scott County website.
The building permit application also triggers a request to the Scott County Highway Department to manufacture and install an emergency “address marker” at the new home site. This address marker is the familiar reflective blue sign showing the actual house number of the residence. It is placed in the road right of way at the driveway access to each occupiable structure in the county. This uniformity of placement makes it easier for emergency responders to locate the driveway entrance to your home. In years past, the fire department assigned a “fire number” to each structure; a unique number used by their department for locating residences. These fire numbers are no longer being used, and if you have an old fire number sign, you may remove it.
Emergency responders, delivery people, and house guests have all expressed appreciation for the “little blue signs” at the end of the driveways in Scott County.
As Scott County continues to grow, the Sheriff’s Office continues to look for new and better ways to quickly and efficiently send emergency responders to homeowners and businesses within the county. We are currently in the process of creating a GPS point database for every parcel in the county, and are discussing the possibility of mapping programs for use in the squad cars.
So…how did I get my address, anyway?
In 1980, an addressing task force was formed in anticipation of the 911 system becoming mandatory in the state in 1983. Previous to that time, rural Scott County was addressed as “Route and Box” numbers, with no official street names. The task force found the municipalities were already using unique addresses, and the cities wanted to stay on their own addressing systems. So, an Addressing Ordinance was adopted by the eleven townships and the city of Elko. Recently, the combined cities of Elko New Market have also chosen to adopt this ordinance.
The Uniform Addressing Ordinance placed the eleven townships and Elko on a grid, with Baseline Avenue as the “zero” point in the county for E-W addresses. Addresses running generally in this direction receive street NAMES. Streets running generally N-S receive street NUMBERS and the grid runs from 115th St in the north, to 280th St in the south, the southernmost border of the county, Highway 19. Properties on the north and west sides of the street are assigned even numbers, those on the south and east sides of the street are assigned odd numbers. Numbering allows 1000 numbers per mile, or 500 for each side of the road.
When a new plat is recorded, the Addressing Coordinator will assign house numbers according to the addressing grid. New developments are checked to ensure the same street name is not used within townships, emergency service zones, or postal areas. These new addresses, including house numbers and street names, are then sent to the 911 Board, the Sheriff’s Office, the Fire Department and Ambulance service covering the area of development, the school district, voter registration, utilities, and the developer. The developer is responsible for placing street intersection signs within the development, with sign standards consistent with county policy.
The addresses are also added to the Computer Aided Dispatch system used by the dispatchers to take calls and send them to officers in their squads, and a mapping program that will plot (map) calls for the dispatcher when a call is received. That same database used in the mapping program is also used to populate the street names for the maps on the Scott County website.
When a resident applies for a building permit for a home, the address assigned to the particular lot on the plat is recorded on the permit and entered into the taxation records with a parcel ID number, or PIN. The data from this entry is used to populate the house numbers for the maps on the Scott County website.
The building permit application also triggers a request to the Scott County Highway Department to manufacture and install an emergency “address marker” at the new home site. This address marker is the familiar reflective blue sign showing the actual house number of the residence. It is placed in the road right of way at the driveway access to each occupiable structure in the county. This uniformity of placement makes it easier for emergency responders to locate the driveway entrance to your home. In years past, the fire department assigned a “fire number” to each structure; a unique number used by their department for locating residences. These fire numbers are no longer being used, and if you have an old fire number sign, you may remove it.
Emergency responders, delivery people, and house guests have all expressed appreciation for the “little blue signs” at the end of the driveways in Scott County.
As Scott County continues to grow, the Sheriff’s Office continues to look for new and better ways to quickly and efficiently send emergency responders to homeowners and businesses within the county. We are currently in the process of creating a GPS point database for every parcel in the county, and are discussing the possibility of mapping programs for use in the squad cars.
VOIP CALLS
Voice over Internet Protocol (VoIP)
WHAT IS INTERCONNECTED VOIP SERVICE?
If you have or are thinking of subscribing to an interconnected VoIP service, you should:
WHAT IS INTERCONNECTED VOIP SERVICE?
- • Interconnected VoIP service allows you to make and receive calls to and from traditional phone numbers, usually using an Internet connection, possibly a high-speed (broadband) Internet connection, such as Digital Subscriber Line (DSL), cable modem, or wireless broadband.
• It can be used in place of traditional phone service.
- • Traditional phone services have generally associated a particular phone number with a fixed address. Portable interconnected VoIP services enable consumers to take their home or business phone service almost anywhere.
• Because certain interconnected VoIP services can be used from virtually any Internet connection, the location of the caller cannot automatically be determined.
• The FCC has recently taken action to make sure that emergency calls from these VoIP services will get through to the appropriate public safety authorities, but there are certain things that consumers need to know.
• When you call 911 from a traditional telephone, the call in most cases is sent to a Public Safety Answering Point (PSAP) that is responsible for helping people in a particular geographic area or community. PSAP personnel often can automatically identify your location and direct the closest emergency personnel to that location. They also often can automatically identify your telephone number so that they can call you back if you are disconnected.
• Because VoIP service works differently from traditional phone service, consumers who use it should be aware that VoIP 911 service may also work differently from traditional 911 service. The FCC and VoIP service providers are striving to eliminate these differences, but some of them are:
§ VoIP 911 call may not connect to PSAP;
§ VoIP 911 service may ring to the administrative line of the public safety answering point (PSAP), which may not be staffed after hours, or by trained 911 operators;
§ VoIP 911 service correctly connected to the PSAP, but did not automatically transmit the user’s phone number and/or location information;
§ VoIP customers may need to provide location or other information to their VoIP providers, and update this information if they change locations, for their VoIP 911 service to function properly;
§ VoIP service may not work during a power outage, or when the Internet connection fails or becomes overloaded.
If you have or are thinking of subscribing to an interconnected VoIP service, you should:
- • Provide your accurate physical address to your interconnected VoIP service provider to ensure that emergency services can quickly be dispatched to your location.
• Be familiar with your VoIP service provider’s procedures for updating your address, and promptly update address information in the event of a change.
• Have a clear understanding of any limitations of your 911 service.
• Inform children, babysitters, and visitors about your VoIP service and its 911 limitations, if any.
• If your power is out or your Internet connection is down, be aware that your VoIP service may not work. Consider installing a backup power supply, maintaining a traditional phone line, or having a wireless phone as a backup.
• If you have questions about whether the phone service you are receiving is an interconnected VoIP service, contact your service provider for further information.